Demo mode. Sample data from a fictional textile mill. Nothing here is a real company, and nothing you click is saved.
Sign in Start free trial
Live demo

See it working before you sign up

This is PlantMaster Pro loaded with one week of sample data from a spinning mill in Karachi. Click any tab. No account, no password, nothing to install.

app.hsbfix.org — demo workspace
Gulshan Textile Mills Site 1 — Korangi, Karachi · Rizwan (Maintenance Manager)
Online
12Open work orders
3Overdue
48Assets tracked
2.4hAvg response time
Needs attention
AC-02 Air Compressor — bearing noise above baseline
Sound level 80 dB against a 72 dB baseline. Rise concentrated in the 4.2 kHz band, which usually points to the drive-end bearing. Flagged 06:12 today.
B-01 Boiler — feedwater pump vibration climbing
Up 18% over fourteen days. Still inside limits, worth watching.
RF-04 Ring Frame — preventive maintenance due in 2 days
Scheduled 18 September. Spindle tape and top roller check.
Today's work
WO-1042 · Compressor tripping on high discharge temperature
AC-02 · Imran Ali · Due today
Open
WO-1041 · Replace spindle tape, section C
RF-04 · Naveed Ahmed · Due 18 Sep
In progress
WO-1039 · Monthly safety valve test
B-01 · Safety team · Was due 14 Sep
Overdue
All work orders — September
WO-1042 · Compressor tripping on high discharge temperature
AC-02 Atlas Copco GA55 · Priority high · Imran Ali · Raised 16 Sep 06:40 by shift operator, via Urdu voice note
Open
WO-1041 · Replace spindle tape, section C
RF-04 Rieter G32 · Priority medium · Naveed Ahmed · 2 of 6 spindles done
In progress
WO-1039 · Monthly safety valve test
B-01 Boiler 8 TPH · Priority high · Safety team · 2 days late
Overdue
WO-1038 · Clean condenser tubes
CH-03 Chiller 120 TR · Asif Mehmood · Closed 15 Sep · 3.5 hours · 2 parts used
Done
WO-1036 · 250-hour service
DG-01 Generator 1000 kVA · Imran Ali · Closed 13 Sep · oil and filters replaced
Done
WO-1034 · Card clothing inspection
CD-07 Rieter C70 · Naveed Ahmed · Closed 11 Sep
Done
Every machine gets a QR sticker
A technician scans it with their phone and lands straight on that machine — history, manual, open jobs. No searching, no asset codes to remember.
Asset register — 6 of 48 shown
AC-02 · Air Compressor
Atlas Copco GA55 · Utilities · 18,420 running hours · 1 open job
Watch
RF-04 · Ring Frame
Rieter G32 · Spinning · 1,008 spindles · PM due 18 Sep
Watch
B-01 · Steam Boiler
8 TPH fire tube · Utilities · last inspection 12 Aug
Healthy
CH-03 · Chiller
120 TR screw · Utilities · serviced 15 Sep
Healthy
DG-01 · Diesel Generator
1000 kVA · Power · 250h service done 13 Sep
Healthy
CD-07 · Carding Machine
Rieter C70 · Spinning · card clothing checked 11 Sep
Healthy
The same question, asked two ways
Every CMMS with AI can give you a generic answer. The difference is whether it has read your equipment manual. Pick a fault and compare the two columns.
Searching…
Without your manuals General AI knowledge only
With your manuals loaded Grounded in your own documents
Sound check — AC-02 Air Compressor
Hold your phone near the machine and record for 30 seconds
The app compares what it hears against the baseline recorded when this machine was known to be healthy. No sensors, no wiring, no extra hardware.
Frequency comparison
60 70 80 90 4.2 kHz +8 dB 0.5k 2k 6k 12k 20k
Baseline, 2 Aug Today, 06:12
Change detected — drive-end bearing
Overall level up from 72 dB to 80 dB. The increase sits almost entirely in the 4.2 kHz band, which is the signature of early bearing wear rather than a load change. A work order has been raised and assigned to Imran Ali.
Manuals and drawings — what a loaded account looks like
You upload the PDFs you already have. We index them at no charge during setup. This is what the AI reads from.
PDF
Atlas Copco GA55 — Instruction Book
312 pages · indexed · linked to AC-02
PDF
Rieter G32 Ring Spinning Machine — Service Manual
208 pages · indexed · linked to RF-04
PDF
8 TPH Fire Tube Boiler — Operation & Maintenance
96 pages · indexed · linked to B-01
Why this matters
The AI only answers from these documents. It quotes the page number so a technician can check it. It will say it does not know rather than invent a procedure for your equipment.
Demo workspace · sample data · PlantMaster Pro by HSB Fix Services

Want this with your own machines in it?

Seven days free. We load your equipment list and your manuals for you, at no charge. If it does not suit you, nothing happens when the trial ends.

Start 7-day free trial Ask a question

Or see what it costs.